2009 Harley-Davidson XL1200C Sportster Custom,only 2,972mis,Vivid Black with Vance & Hines Exhaust,Engine Guard,HD Pegs and Grips.
1999 Chevrolet Silverado 1500 1999 Chevrolet 1500 Silverado
Custom steering wheel with mounting collar and horn button, excellent condition
I have a brand new set of front TMI seat covers for a 1973 Beetle or Super Beetle. These are have bright white trim with full sapphire blue cloth, cushioned inserts. They are unused and still in the TMI box. They normally cost about $310 + shipping and handling from the online vendors. I decided to go in a different direction, my loss is your gain. Prices is shipped in the lower 48 states, anyw...
Selling a set of Porsche 914 2.0 stainless steel heat exchangers. 2 of the ears have a small crack at the base of the weld, but nothing that will affect use. This happens when people tighten past the recommended 16 ft lbs.
Have a bay bus with an inoperable odomoeter? Your problem could be a cracked speedometer drive gear that is just spinning on the odometer wheel shaft. Fresh from my 3D printer and based on my own 3D model are these 11-tooth speedo drive gears for MPH bus speedometers. With the correct, slight helical cut on the teeth, these gears mesh well with the speedometer's worm drive to restore function t...
Created to meet a need I had for my Westy, my 3D-printed Westy sink faucet mounting plates replace the NLA original part. They can be printed in different colored filaments that I already have (white, black, translucent blue, yellow, orange, red, yellow, silver-gray, stainable wood filament) or, if you really need it in another color, we can talk about sharing the cost of that filament (always ...
Davinci 1250 CFM big gun alcohol dominator. Used for 3 dyno pulls and is in NEW condition. Hard anodized bowls, Billet metering blocks, Braswell floats, Titanium needle and seats, 1 piece linkage. Perfect for larger cubic inch engines. Asking price includes shipping to lower 48 states. Contact Bill @ 502-718-2020. hawk6110. Mt. Washington, KY 40047 (502) 718-2020
I have too many carbs! It's time to thin out the herd #2 of 2! Holley Ultra HP "950" 1.60" venturi carburetor converted to annular boosters in very nice used condition. NOTE: This will be sold as a PARTS KIT to be assembled and tuned for the end user's application! Although I did test it briefly using different boosters and metering blocks than will be included here, I didn't manage to get it s...
I own too many carburetors and have decided to sell a couple. This one is a QFT/Proform-type "950" 1.45" venturi 4150 built from all new parts: => Suggested application: A 4150 street/strip carb for a serious 400+" stroker small-block or moderate 450-500" big-block in the 550 - 650 HP range - The moderate 1.45" venturi size helps maintain decent street manners - Flows enough to support 650+ HP ...
todos los motores.que se venden van con poco millaje y garantia y buenos precios
BBC EFI COMPLETE BOLT ON TURN KEY SET UP SHOULD BE ABLE HANDLE WELL 0VER 1200HP ACCUFAB 2200 CFM POLISHED THROTTLE BODY W/ IAC MOTOR AND THROTTLE POSITION SWITCH F.A.S.T EZI EFI WITH HARNESS AND HAND HELD PROGRAMMER. INCLUDING ALL SENSORS AIR TEMP SENSOR, WATER TEMP SENSOR, MAP SENSOR AND OXYGEN SENSOR RECTANGULAR PORT ALUMINUM POLISHED INTAKE BILLET EFI FUEL PRESSURE REGULATOR W/ BOOST SENSOR ...
COMPLETE and Fresh (June 2018) 632 with dyno pulls and 5 1/8 miles passes (3 of which were half track) since complete freshen up ($7888). 4.92 in 2450 pound car. I have dyno sheet and invoice for serious buyers. List of parts as follows. Merlin Block Callies Crank Oliver Rods Race Tec gas ported pistons Profiler Heads 16 NEW Titanium Valves ($1920) T&D Shaft Rockers Jesel Belt Drive (New belt a...
I have 4 5.5 painted wheels for 66-67 bug SORRY THESE HAVE BEEN SOLD STILL HAVE 2 4.5 in wide chrome reverse wheels for pre 65 for sale
Matching pair of 840 castings rectangle port closed chambers, dated 12-30-68, never machined or messed with, I have all the factory valves and hardware,. WoodbineWelding. Woodbine, MD 21797 (443) 398-6075
Description: Firebird parts for sale, all are or best offer, plus shipping; - Rally II wheels, all 14 , three KM wheel codes, all 14 x 6 , rim stamp dates of manufacture, two are 5-15-78 and one is 2-20-82. One KX, 14 x 6 , 11-3-83. $80 each - 1969 standard carrier and 2.78:1 ring and pinion gears $75 - 1969-72 8-track floor mounting bracket $15 - 1967-68 & 1970-81 automatic transmission brake ...
Description: ORIGINAL, LIKE NEW CONDITION WITH NOS LABLE STILL ATTACHED